This project details how to connect Opto-Isolated Relay Board to an AVR development board and control it via Text message (SMS)
BASCOM Source Code
Hardware | Description |
---|---|
![]() | Atmel AVR Microcontroller Development System This kit was kindly provided to me by the friendly people over at http://www.btinternet.com/~e2one/avrbrd/ |
![]() | 8×24 LCD Display Details of how to wire up a 8×24 display to the development board can be found at http://www.btinternet.com/~e2one/avrbrd/ (see the 8×24 LCD Project). If you use a smaller display then you will have to modifying the code to suit. |
![]() | Relay board Opto-Isolated Relay Board, includes 4 channels for remote control of Mains appliances and circuits. Ideal for home control and industrial applications. Each channel is controlled by a TTL input and can easily be controlled by a microcontroller or control system. et-opto_relay4_manual.pdf |
![]() | Relay cable Cable to wire the AVR board to the relay board |
![]() | A mobile phone I used a NOKIA 7110 but any phone that has a built in modem should be ok. |
![]() | A DLR-3 cable A phone connector wired to a DB9-F If you don't have one or you can't afford to buy it then there are some good solutions for making your own. |
As the ATMEL AT90S2313 only has 2k of code space the demo version of BASCOM can be used without hitting any of its restrictions.
Block diagram of the basic components used in the SMS Relay project.
A great site for the wiring of all things RS232 can found at http://www.lammertbies.nl/comm/cable/RS-232.html
9 Pin Connector on a DTE device (Phone connection)
Pin Number | Direction of signal: |
---|---|
1 | Carrier Detect (CD) (from DCE) Incoming signal from a modem |
2 | Received Data (RD) Incoming Data from a DCE |
3 | Transmitted Data (TD) Outgoing Data to a DCE |
4 | Data Terminal Ready (DTR) Outgoing handshaking signal |
5 | Signal Ground Common reference voltage |
6 | Data Set Ready (DSR) Incoming handshaking signal |
7 | Request To Send (RTS) Outgoing flow control signal |
8 | Clear To Send (CTS) Incoming flow control signal |
9 | Ring Indicator (RI) (from DCE) Incoming signal from a modem |
Nokia 7110 DLR-3
Pin | Signal | Specs |
---|---|---|
1 | V In | 0..8.5V, 0..850mA |
2 | Chrg Control | PWM, 32..37 Hz, 1..99% |
3 | XMic / Device Selector | |
4 | SGnd / DLR-3 VCC | 3.3 V |
5 | XEar / DLR-3 RTS | |
6 | MBus | 9600bps |
7 | FBus Rx / Modem | 9600 - 230.400 bps < 0.8V : '0' > 2.0V : '1' |
8 | FBus Tx / Modem | 9600 - 230.400 bps < 0.8V : '0' @ max. 4mA > 1.7V : '1' @ max. 4mA |
9 | LGnd |
The standard cable that is supplied with the AVR development kit uses a 3 pin configuration for RS232 data. It is wired as a DTE with built in loop back handshaking.
AVR RS232 DB9 wiring
The DLR-3 cable expects partial handshaking from a DCE. The problem is the AVR board does not implement any hardware handshaking and is wired as a DTE.
To overcome this problem we will build a new cable. This will be wired so that the AVR board is seen as DCE, additionally it will also have a hardwired active DTR signal.
AVR board IDC | Connector | Function |
---|---|---|
1 | 5 | Signal ground |
2 | 3 | Tx → Rx |
3 | 2 | Rx → Tx |
4 | 4 | Vcc → DTR |
The purpose of this null modem cable is to make the phone think there is a DCE device listening
It's a bit annoying that the Schematic for the development board does not match those on the board. Each pin is swapped for the wiring of the LCD.
So to wire a suitable cable the following mapping can be used
LCD Board | 6 Pin IDC |
---|---|
1 | Vcc |
3 | Out0 - PB2 |
5 | Out1 - PB3 |
12 | Out2 - PB4 |
13 | Out3 - PB7 |
8 | Gnd |