Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
arduino:isp_with_stk500 [2012/12/19 11:15] – brett | arduino:isp_with_stk500 [2013/08/27 06:14] – [AVRDUDE with AVRISP on Linux] brett | ||
---|---|---|---|
Line 73: | Line 73: | ||
< | < | ||
- | [root@wombat avrisp]# avrdude -v -c avrisp2 -p m328p -P /dev/ttyUSB0 -b 115200 -Uflash: | + | #!/bin/sh |
+ | # | ||
+ | # Using ESX you can virtually connect the AVR Programer into the VM | ||
+ | # This command will drive the AVR ISP and flash a chip | ||
+ | # YELLOW WIRE is PIN 1 | ||
+ | # Power to AVR UNIT | ||
+ | # Power to Arduino | ||
- | avrdude: Version 5.10, compiled on Dec 19 2012 at 21:20:20 | + | avrdude |
- | | + | -U efuse:w:0x05:m \ |
- | | + | -U hfuse:w:0xde:m \ |
- | + | -U lfuse:w:0xff:m \ | |
- | | + | -U flash:w: |
- | User configuration file is "/ | + | |
- | User configuration file does not exist or is not a regular file, skipping | + | |
- | + | ||
- | Using Port : / | + | |
- | Using Programmer | + | |
- | | + | |
- | AVR Part : ATMEGA328P | + | |
- | Chip Erase delay : 9000 us | + | |
- | | + | |
- | | + | |
- | RESET disposition | + | |
- | RETRY pulse : SCK | + | |
- | | + | |
- | | + | |
- | | + | |
- | | + | |
- | | + | |
- | | + | |
- | | + | |
- | | + | |
- | | + | |
- | | + | |
- | + | ||
- | Block Poll | + | |
- | | + | |
- | ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- --------- | + | |
- | | + | |
- | | + | |
- | | + | |
- | | + | |
- | efuse | + | |
- | | + | |
- | | + | |
- | | + | |
- | + | ||
- | | + | |
- | | + | |
- | | + | |
- | Hardware Version: 15 | + | |
- | | + | |
- | | + | |
- | SCK period | + | |
- | + | ||
- | avrdude: AVR device initialized and ready to accept instructions | + | |
- | + | ||
- | Reading | ################################################## | + | |
- | + | ||
- | avrdude: Device signature = 0x1e950f | + | |
- | avrdude: safemode: lfuse reads as 62 | + | |
- | avrdude: safemode: | + | |
- | avrdude: safemode: efuse reads as 7 | + | |
- | avrdude: NOTE: FLASH memory has been specified, an erase cycle will be performed | + | |
- | To disable this feature, specify the -D option. | + | |
- | avrdude: erasing chip | + | |
- | avrdude: reading input file " | + | |
- | avrdude: input file jeenode-rf12demo-bootloader.hex auto detected as Intel Hex | + | |
- | avrdude: writing flash (32670 bytes): | + | |
- | + | ||
- | Writing | ################################################## | + | |
- | + | ||
- | avrdude: 32670 bytes of flash written | + | |
- | avrdude: verifying flash memory against jeenode-rf12demo-bootloader.hex: | + | |
- | avrdude: load data flash data from input file jeenode-rf12demo-bootloader.hex: | + | |
- | avrdude: input file jeenode-rf12demo-bootloader.hex | + | |
- | avrdude: input file jeenode-rf12demo-bootloader.hex contains 32670 bytes | + | |
- | avrdude: reading on-chip flash data: | + | |
- | + | ||
- | Reading | ################################################## | + | |
- | + | ||
- | avrdude: verifying ... | + | |
- | avrdude: 32670 bytes of flash verified | + | |
- | + | ||
- | avrdude: safemode: lfuse reads as 62 | + | |
- | avrdude: safemode: hfuse reads as D9 | + | |
- | avrdude: safemode: efuse reads as 7 | + | |
- | avrdude: safemode: Fuses OK | + | |
- | + | ||
- | avrdude done. Thank you. | + | |
- | + | ||
- | [root@wombat avrisp]# | + | |
</ | </ | ||
{{tag> | {{tag> |