Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
| atmel:n76e003 [2019/09/28 21:28] – minerva9 | atmel:n76e003 [2019/09/28 22:36] – minerva9 | ||
|---|---|---|---|
| Line 18: | Line 18: | ||
| \\ | \\ | ||
| {{: | {{: | ||
| + | \\ | ||
| + | \\ | ||
| + | Note: Whilst the above picture is a good overview, it doesn' | ||
| \\ | \\ | ||
| \\ | \\ | ||
| Line 23: | Line 26: | ||
| The board that I have (as pictured above) measures about 42mm x 30mm. It's pretty small, yet space has been made for four M3 mounting holes. | The board that I have (as pictured above) measures about 42mm x 30mm. It's pretty small, yet space has been made for four M3 mounting holes. | ||
| - | The chip is centrally positioned. This board has a Mini-B USB connector fitted. Seems that this is just used to feed 5V to the board - the data lines on the connector don't seem to be hooked up to anything. A surface mounted LED lights up when power is applied via the Micro-B. The other LED on the board is attached (via a resistor) to port pin P15 - the Jumper ' | + | The chip is centrally positioned. This board has a mini-B USB connector fitted. Seems that this is just used to feed 5V to the board - the data lines on the connector don't seem to be hooked up to anything. A surface mounted LED lights up when power is applied via the mini-B. The other LED on the board is attached (via a resistor) to port pin P15 - the Jumper ' |
| \\ \\ | \\ \\ | ||
| The chip can work at supply voltages between 2.4V and 5.5V. The board uses a AMS1117 3.3V regulator to drop the 5V USB fed line. Not sure why they bothered, but there we have it. I've seen a variant of this board that is fitted with a 5V/3.3V selector switch. | The chip can work at supply voltages between 2.4V and 5.5V. The board uses a AMS1117 3.3V regulator to drop the 5V USB fed line. Not sure why they bothered, but there we have it. I've seen a variant of this board that is fitted with a 5V/3.3V selector switch. | ||
| Line 29: | Line 32: | ||
| \\ | \\ | ||
| - | === A few words about the key feature | + | === A few words about the key features |
| - | Key Features: | ||
| Core | Core | ||
| - 1T 8051 processor | - 1T 8051 processor | ||
| - | - Max frequency up to16 MHz | + | - Max frequency up to 16MHz |
| - Wide operating voltage: 2.4V to 5.5V | - Wide operating voltage: 2.4V to 5.5V | ||
| - Temperature range: -40℃ to 105℃ | - Temperature range: -40℃ to 105℃ | ||
| Line 56: | Line 58: | ||
| - One I²C up to 400 kHz | - One I²C up to 400 kHz | ||
| Clock Control | Clock Control | ||
| - | - < 2% deviation16 | + | - < 2% deviation 16 MHz Internal RC oscillator |
| - 10 kHz Internal RC oscillator | - 10 kHz Internal RC oscillator | ||
| Part No. | Part No. | ||
| Line 98: | Line 100: | ||
| === Some ideas === | === Some ideas === | ||
| - | This chip has both user program and bootloader areas. It should be possible to use the Nuvotron | + | This chip has both user program and bootloader areas. It should be possible to use the Nuvoton |
| \\ | \\ | ||
| ToDo: Need to find out if the board comes pre-supplied with a bootloader. | ToDo: Need to find out if the board comes pre-supplied with a bootloader. | ||