Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
blog:freenas_11.2-u5_and_10gbe [2019/08/23 14:28] – brett | blog:freenas_11.2-u5_and_10gbe [2019/08/23 14:36] (current) – brett | ||
---|---|---|---|
Line 1: | Line 1: | ||
====== FreeNAS 11.2-U5 and 10Gbe ====== | ====== FreeNAS 11.2-U5 and 10Gbe ====== | ||
- | This is just a note as I see a lot of posts out there saying use Chelsio cards for FreeNAS as they are well supported. | + | This is just a note as I see a lot of posts out there saying use Chelsio cards for FreeNAS as they are well supported. |
+ | < | ||
+ | Aug 9 18:45:00 ale cxgbc0: <Chelsio T310, 1 port> mem 0xfb881000-0xfb881fff, | ||
+ | 42 at device 0.0 on pci10 | ||
+ | Aug 9 18:45:00 ale kernel: PHY 0 i2c read of dev.addr a0.0 timed out | ||
+ | Aug 9 18:45:00 ale kernel: PHY 0 i2c read of dev.addr a0.0 timed out | ||
+ | Aug 9 18:45:00 ale cxgbc0: using MSI-X interrupts (9 vectors) | ||
+ | Aug 9 18:45:00 ale kernel: found old FW minor version(7.10), | ||
+ | Aug 9 18:45:00 ale kernel: found old FW minor version(7.10), | ||
+ | Aug 9 18:45:00 ale cxgbc0: firmware needs to be updated to version 7.11.0 | ||
+ | Aug 9 18:45:00 ale cxgb0: <Port 0 10GBASE-R> | ||
+ | Aug 9 18:45:00 ale cxgb0: Using defaults for TSO: 65518/ | ||
+ | Aug 9 18:45:00 ale cxgb0: Ethernet address: 00: | ||
+ | Aug 9 18:45:00 ale cxgbc0: Firmware Version 7.10.0 | ||
+ | </ | ||
+ | Firmware update - I don't think this was necessary as the driver auto updates we just need a reboot | ||
+ | < | ||
+ | cxgbtool cxgb0 loadfw t3fw-7.11.0.bin | ||
+ | Reboot | ||
+ | </ | ||
+ | Next time around the firmware has been updated | ||
+ | < | ||
+ | Aug 9 18:55:44 ale cxgbc0: using MSI-X interrupts (9 vectors) | ||
+ | Aug 9 18:55:44 ale cxgb0: <Port 0 10GBASE-R> | ||
+ | Aug 9 18:55:44 ale cxgb0: Using defaults for TSO: 65518/ | ||
+ | Aug 9 18:55:44 ale cxgb0: Ethernet address: 00: | ||
+ | Aug 9 18:55:44 ale cxgbc0: Firmware Version 7.11.0 | ||
+ | </ | ||
+ | The drive is plumbed into the kernel but the link won't come up to ACTIVE. | ||
+ | |||
+ | I was using SPF+ CISCO Passive Twinax cable [[https:// | ||
MNPA19-XTR | Mellanox EN ConnectX-2 1-Port 10GbE Network Adapter | MNPA19-XTR | Mellanox EN ConnectX-2 1-Port 10GbE Network Adapter | ||
Line 24: | Line 54: | ||
Aug 22 19:52:55 ale kernel: mlx4_en: mlxen0: Initializing port | Aug 22 19:52:55 ale kernel: mlx4_en: mlxen0: Initializing port | ||
</ | </ | ||
- | ifconfig output for the device | + | ifconfig output for the device. Its alive and happy. |
< | < | ||
- | root@ale[~]# | + | mlxen0: flags=8943<UP,BROADCAST, |
- | mlxen0: flags=8802< | + | options=ad00b9< |
- | options=ed07bb<RXCSUM,TXCSUM, | + | |
ether 00: | ether 00: | ||
hwaddr 00: | hwaddr 00: | ||
+ | inet 192.168.1.22 netmask 0xffffff00 broadcast 192.168.1.255 | ||
nd6 options=9< | nd6 options=9< | ||
- | media: Ethernet autoselect (autoselect | + | media: Ethernet autoselect (10Gbase-SR |
status: active | status: active | ||
root@ale[~]# | root@ale[~]# |