Both sides previous revision Previous revision Next revision | Previous revision |
livebox:commandlineaccess [2013/03/30 09:14] – Replaced Console access hardware pictures brett | livebox:commandlineaccess [2013/09/11 18:29] (current) – [via the Serial Port] minerva9 |
---|
| |
- an MMJ to RJ11 cable | - an MMJ to RJ11 cable |
- a PCB that holds the Max3232cpe device & has RJ11 and RJ45 connectors | - a PCB that holds the Max3232cpe device & has RJ11 and RJ45 connectors, caps & diodes |
- an original Cisco console cable (worth £5 alone) RJ45 to DB9 | - an original Cisco console cable (worth £5 alone) RJ45 to DB9 |
- 5x 1uf 50v caps | |
- 2x 1n4004 diodes | |
| |
We don't provide a case for the PCB - this is left as an exercise for the reader (some, less fussy, readers simply wrap the entire PCB with insulating tape). | We don't provide a case for the PCB - this is left as an exercise for the reader (some, less fussy, readers simply wrap the entire PCB with insulating tape). |
</note> | </note> |
| |
{{:livebox:cimg1759.jpg?320 }} Making an RS232 adaptor. Crimped up a RJ11 6P6C onto a piece of cat5 cable. Repurposed a PCB which has a Max232 onboard to do the hookup. N.B. The chip needed for this convertor is the MAX3232 - this works at 3.3V (costs rather more than a MAX232 - tried a MAX232, it doesn't work). Turns out that the serial port socket on the Livebox isn't a 'standard' RJ11 connector - it is a MMJ connector with the retaining clip offset from the centre of the socket - a standard RJ11 needs to have its clip cut off to allow the connector to enter. This gives 'reduced' insertion force, but there is a slight resistance - just enough to keep the connector in place. | {{:livebox:cimg1759.jpg?320 }} Making an RS232 adaptor. Crimped up a RJ11 6P6C onto a piece of cat5 cable. Repurposed a PCB which has a Max232 onboard to do the hookup. N.B. The chip needed for this convertor is the MAX3232 - this works at 3.3V (costs rather more than a MAX232 - tried a MAX232, it doesn't work). Turns out that the serial port socket on the Livebox isn't a 'standard' RJ11 connector - it is a MMJ connector with the retaining clip offset from the centre of the socket - a standard RJ11 needs to have its clip cut off to allow the connector to enter. This gives 'reduced' insertion force, but there is a slight resistance - just enough to keep the connector in place - not great for permanent setups. |
| |
{{http://farm4.static.flickr.com/3070/2786661562_8513d3cb3b_m.jpg}} | {{http://farm4.static.flickr.com/3070/2786661562_8513d3cb3b_m.jpg}} |
| |
So now getting in is going to be so much easier. Just change the Livebox Name (in browser UI menu Configuration→Advanced→Wireless) to each of the following in sequence: This works with UK firmware: 5.04.3. We only have 32 characters to play with in the wireless name so it must be entered as seen. | So now getting in is going to be so much easier. Just change the Livebox Name (in browser UI menu Configuration→Advanced→Wireless) to each of the following in sequence: This works with UK firmware: 5.04.3. We only have 32 characters to play with in the wireless name so it must be entered as seen. |
| |
| First change the livebox hostname to what is below and Save. |
<code> | <code> |
;echo root::0:0:::/bin/sh>/tmp/x | ;echo root::0:0:::/bin/sh>/tmp/x |
| </code> |
| Then change the livebox hostname to what is below and Save. |
| <code> |
;cp /tmp/x /etc/passwd | ;cp /tmp/x /etc/passwd |
</code> | </code> |