Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
livebox:hah_hahnode:airwick [2012/05/20 00:45] – [Airwick HAHNode] brett | livebox:hah_hahnode:airwick [2013/08/16 07:35] – minerva9 | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | ====== Airwick | + | ====== Airwick |
- | {{http:// | + | {{6929394483_150611e518_q.jpg }} |
- | The Airwick iMotion Freshmatic Compact makes an ideal housing for a [[/ | + | The Airwick iMotion Freshmatic Compact makes an ideal housing for a [[/ |
- | Each Airwick roomNode adds one temperature sensor (via a DS18B20), movement detection via the inbuilt Airwick PIR, light level detection via an LDR and a low battery warning (the batteries last for a very long time). Totally wireless in operation, so just place the roomNode where you need to take the readings. | + | Each Airwick roomNode adds one temperature sensor (via a DS18B20), movement detection via the inbuilt Airwick PIR, light level detection via an LDR and a low battery warning (the batteries last for a long time). Totally wireless in operation, so just place the roomNode where you need to take the readings. |
- | You can buy the roomNode Airwick kit from the Shop. This kit includes includes all connector cables and sensors. | + | You can buy the roomNode Airwick kit from the [[http:// |
An assembled roomNode control unit showing the location for each of the sensors used by the Airwick. | An assembled roomNode control unit showing the location for each of the sensors used by the Airwick. | ||
Line 14: | Line 14: | ||
{{: | {{: | ||
- | ===== Assembly instructions for the roomNode Airwick kit ===== | ||
- | Click on an image for a larger view. | + | Note: the difference between v1.2 of the PCB and v1.3 is that the later has a ground plane to help with RF signal strength. Also note that the orientation of the electrolytic capacitor is also changed on the v1.3 board.\\ |
+ | //v1.2 was produced in small quantities to verify the design.// | ||
- | || Buy an Airwick. Note that we are talking about the Airwick ' | + | jeenodeApplet.lua applet configuration as node 3 and enabling all the sensors available. |
- | || The enclosure is disassembled by removing the four silver screws (some models use standard crosspoint screws - others use triangular slotted ' | + | <code lua> |
- | || The Airwick PCB is attached to the enclosure by two crosspoint screws. Undo these to release the PCB. Don't lose them as they are needed later on to reattach the PCB. || {{http:// | + | [3] = RoomNode{base=" |
- | || The Airwick PCB has three connectors. These are coloured black, white and red. Unplug all three connectors and remove the little solenoid that is wired to the white connector. Remove the switch that is wired to the black connector. | + | </code> |
- | || Inside the battery half - see the RED connector we will desolder the matching female and reuse this on the HAHNode to reattach the battery || {{http:// | + | ===== Assembly instructions |
- | || Next, we have to make a few modifications to the Airwick PCB. These isolate power from the existing controller chip on the Airwick PCB and allow this PCB to be powered from the HAHnode board. We tap the filtered signal from the PIR and feed this to the HAHnode. When handling the PCB, be careful not to touch the PIR sensor module. Note that if your Airwick board is different from the one pictured below, you might have to alter the following procedure (however, we've yet to hear of a different one). \\ There are eight track cuts in total. We used a 2mm end mill, so our cuts look like small white circles, but a small drill, scalpel or stanley knife will also be good (mind you don't cut off any of your fingers!). On the following images, we put a small orange dot in the centre of our cuts so you can spot them more easily. It's best to use ' | + | |
- | || There are three wires that need to be soldered onto the Airwick PCB. These connect power/ | + | |
- | || We cut away the plastic part that used to hold the canister. This allows better access to the HAHnode PCB.\\ Initially I left too much tube, the arrow shows where to cut, I used a hacksaw, just above the tongues. || {{http:// | + | |
- | || Wire up the LDR sensor. Don't forget to fit the little white grommet - this makes for a nicer finish when the LDR is mounted in the Airwick | + | |
- | || Wire up the DS18B20 Temp sensor. The insulation tube that is supplied is heatshrink. A quick blast from your heatshrink gun (or a paint stripper gun) will do the job. || {{http:// | + | |
- | || Attach sensors || {{http:// | + | |
- | || Fit components into the case.\\ Note the RED mating battery connector now mounted on the RoomNode PCB. || {{http:// | + | |
- | || Fit the batteries (we use decent alkaline ones). Job done || {{http:// | + | |
- | || Almost :) || {{http:// | + | |
- | When first powered | + | <box green round 30%> |
+ | **Click | ||
+ | </box> | ||
- | The HAHnodes transmit immediately when a new PIR event occurs. If there is no motion detected | + | || Buy an Airwick. |
+ | || The enclosure is disassembled by removing the four silver screws (some models use standard crosspoint screws - others use 1.8mm triangular slotted ' | ||
+ | || The Airwick PCB is attached to the enclosure by two crosspoint screws. Undo these to release the PCB. Don't lose them as they are needed later on to reattach the PCB. || {{6783270542_8210632c0d_b.jpg? | ||
+ | || The Airwick PCB has three connectors. These are coloured black, white and red. Unplug all three connectors and remove the little solenoid that is wired to the white connector. Remove the switch that is wired to the black connector. | ||
+ | || Inside the battery half - see the RED connector. We will desolder the matching female and reuse this on the HAHNode to reattach the battery || {{6929389747_c55e57c64c_b.jpg? | ||
+ | || Next, we have to make a few modifications to the Airwick PCB. These isolate power from the existing controller chip on the Airwick PCB and allow this PCB to be powered from the HAHnode board. We tap the filtered signal from the PIR and feed this to the HAHnode. When handling the PCB, be careful not to touch the PIR sensor module. Note that if your Airwick board is different from the one pictured below, you might have to alter the following procedure (however, we've yet to hear of a different one). \\ There are eight track cuts in total. We used a 2mm end mill, so our cuts look like small white circles, but a small drill, scalpel or stanley knife will also be good (mind you don't cut off any of your fingers!). On the following images, we put a small orange dot in the centre of our cuts so you can spot them more easily. It's best to use ' | ||
+ | || There are three wires that need to be soldered onto the Airwick PCB. These connect power/ | ||
+ | || We cut away the plastic part that used to hold the canister. This allows better access to the HAHnode PCB.\\ Initially I left too much tube, the arrow shows where to cut, I used a hacksaw, just above the tongues. || {{6783272238_1202d4a576_b.jpg? | ||
+ | || Wire up the LDR sensor. Obviously, polarity of the connection is unimportant. Don't forget to fit the little white grommet - this makes for a nicer finish when the LDR is mounted in the Airwick case. || {{http:// | ||
+ | || Wire up the DS18B20 Temp sensor. Image shows the flat face of the part facing the camera. The insulation tube that is supplied is heatshrink. A quick blast from your heatshrink gun (or a paint stripper gun) will do the job. || {{6783273502_f2bfcdaa68_b.jpg? | ||
+ | || Attach sensors || {{6929391161_584aa1d219_b.jpg? | ||
+ | || Fit components into the case.\\ Note the RED mating battery connector now mounted on the RoomNode PCB. || {{6783274192_27a946aa67_b.jpg? | ||
+ | || Fit the batteries (we use decent alkaline ones). Job done || {{6783274582_a17847fc3f_b.jpg? | ||
+ | || Almost :) || {{6929394351_ea75e39bc9_b.jpg?320}} || | ||
- | //Many thanks | + | When first powered on, the PIR needs a little time to settle. If you haven' |
- | ===== Other Airwick hack sites ===== | + | The nodes transmit immediately when a new PIR event occurs. If there is no motion detected by the PIR for 2mins 30secs, an ' |
+ | |||
+ | //Many thanks to Kevin for taking these lovely photos and allowing us to use them.// | ||
+ | ====== Other Airwick hack sites ====== | ||
There are several sites which show how others have modified the Airwick Compact unit. | There are several sites which show how others have modified the Airwick Compact unit. |